64 Hanmer St E, Barrie, ON L4M 6V6
Call Us : 249-288-3378
Ask For A Quote Email Us Now
Call Us : 249-288-3378
Ask For A Quote Email Us Now
Some homeowners notice it in the shower, some notice spots on the dishes, and some property managers hear it from a tenant: the water has gone hard again. At Townhouse Plumbing, our answer is the same for all of them. A water softener that is not regenerating has usually lost one of four things: power and the right time on its clock, salt that can actually turn into brine, a clear path for that brine to reach the resin, or a setting that matches your water. Check them in that order. The first two take a few minutes and need no tools.
Three things change the answer in your house. A timer softener and a metered softener fail in different ways, the age of the unit decides whether parts are still worth buying, and the hardness of your own water decides how often the softener needs to work. Keep your owner’s manual beside you, because every valve has its own buttons.
Hard water does not always mean the softener skipped its cycle, because a cycle can run and still do nothing useful. Start with the display on the control valve. A blank screen points to power, a flashing clock points to a power cut, and an error code means the valve itself has found a fault, so look that code up in your manual before you change anything.
Next, look at the salt level. Has it gone down at all over the past few weeks? If the salt has not gone down at all, the softener is probably not drawing brine. Then check the schedule. One manufacturer’s manual gives 2 a.m. as the typical preprogrammed time for the cycle, so a softener that runs at night can fail for weeks without anyone hearing it.
If the unit regenerates when you ask it to but the water stays hard, the trouble is further along, in the brine or the resin.
An electric softener with no power cannot start a cycle, so first make sure it is plugged in and that the outlet works. Some softeners run on water pressure alone and have no plug. On one of those, skip this step and go to the salt.
A power cut causes a quieter problem. One valve maker’s manual says that if the valve misses a scheduled regeneration because of a power failure, it queues one and runs it at the next programmed time. A wrong clock looks fine on the day it happens, because the water stays soft on what is left in the resin. Then the cycle runs at the wrong hour, or not at all, and the hard water arrives without warning a few days later.
Reset the time of day the way your manual describes, then start a manual regeneration with the button or menu the manual names. Watch the display step through its stages. If the valve will not start a cycle even on command, the control valve or its motor has likely failed, so call a plumber rather than keep pressing buttons.
The softener never uses the salt directly. Water in the brine tank dissolves the salt into brine, and the valve draws that brine through the resin to recharge it. If the brine is weak, the resin is only partly recharged and hard water slips through.
A tank can look full and still make no brine. In a salt bridge, a hard crust forms across the tank above the water, and the salt on top sits on that crust without ever getting wet. Press down gently with a broom handle. If it stops on something solid and then breaks through to an empty space, you have found a bridge, and you can break it up with something blunt that will not crack the tank. If you find a layer of hard sludge at the bottom instead, empty the tank, clean it and refill it.
A salt bridge today becomes hard water next week. A weak brine quietly leaves the resin half recharged, and scale builds on your fixtures before you see it.
Standing water in the brine tank is not always a fault. Your manual tells you what level is normal for your model. A level that never drops during the brine draw is the sign worth noting.
Use only salt sold for water softeners, keep the lid on, and keep the salt above the water line. Clean the brine tank whenever you find sludge at the bottom. If you have just refilled an empty tank, one manual says to wait at least 2 hours before regeneration.
What if the clock is right, the salt is loose and the cycle runs? Start a manual regeneration and watch the water in the brine tank during the brine-draw stage. Your manual says when that stage runs. Many units refill the tank later in the same cycle, so a level that matches before and after the cycle proves nothing. If the level does not drop during the brine draw, the softener is not drawing brine. The usual places to look are the injector, which is the small part in the valve that pulls brine out of the tank, the brine line between the two tanks, the float in the brine tank, and the drain line, which has to be clear for the cycle to flush.
A kinked line can be straightened by hand, but a blocked injector or a stuck float is a job for a plumber, who takes the valve apart and confirms which part has stopped before anything is replaced.
A metered softener usually regenerates after so many gallons of water have been softened. A timer softener regenerates on a fixed schedule whether the resin needs it or not. Both depend on knowing how hard your water is.
Penn State Extension works through an example. A softener with a capacity of 20,000 grains, in a house of four people who each use 75 US gallons a day on water with 10 grains per gallon of hardness, removes 3,000 grains a day and needs to regenerate about every 6 to 7 days. Set the hardness to match your water, and the resin lasts until the next cycle. Set it too low, and the resin runs out first.
That second case is the mistake that looks fine on the day it is made. The water is soft for most of the week, then turns hard for a day or two before each cycle, and it looks exactly like a softener that is not regenerating. How hard is your own water? Test it rather than borrowing a neighbour’s number, compare the result with the hardness on the valve, and change the setting to match.
Check the bypass valve behind the softener too. If someone turned it to bypass during other plumbing work, hard water goes straight past a softener that is working normally.
Resin can be fouled from the water it treats. Penn State Extension notes that turbid water can clog the resin with mud and clay, that bacteria and fungi can form mats in it, and that iron fouling is another common problem. Two signs point here rather than to the salt or the settings. The unit regenerates on time and uses salt, but the water stays hard. Or the water pressure drops through the softener and comes back when you switch it to bypass.
| What you found | What usually makes sense |
|---|---|
| A wrong clock, a salt bridge, a kinked brine line or a low hardness setting | Fix it. These are small jobs on a unit that otherwise works. |
| A blocked injector or a stuck float on a valve that is still supported | Repair the part, following the manual for your valve. |
| A failed control valve with no parts available | Price a replacement. |
| Worn resin on an old unit | Price a replacement. |
| A timer model you would rather swap for one that regenerates only when needed | Price a replacement. |
A U.S. EPA WaterSense technical sheet points to the voluntary NSF/ANSI 44 efficiency rating of 5.0 US gallons of water or less per 1,000 grains of hardness removed. Penn State Extension estimates that one regeneration cycle uses about 50 US gallons of water, so a softener that regenerates only when it needs to saves water and salt each time it waits.
A softener that stops working rarely causes a flood, but it does disrupt the house. The laundry feels rough, the showers leave a film, and scale keeps building inside the water heater until someone deals with it. Fixing it while the problem is still a setting or a salt bridge means the work happens on your schedule, not after a week of hard water. Read why Barrie homeowners address warning signs early if you are unsure whether to wait.
When you call us, we look at the fault first and tell you what we find. Then we answer your questions and suggest the option that suits your home and your budget. If the answer is a new unit, read about water softener installation in Barrie. That page covers new installations, replacements, upgrades and the plumbing connections for softener systems. You can also contact our team and tell us what the softener is doing.
Do not wait until a small softener fault becomes a household disruption. Homeowners and property managers in Barrie can start the same way: note what the display shows, how far the salt has dropped and your hardness number, then call Townhouse Plumbing with it. We want the households we serve to keep calling us for years, not only once.
Most control valves have a regeneration button or a menu item for it. On some models one press queues a cycle for that night, and holding the button starts one now. The steps differ by valve, so follow your manual. If the brine tank was empty, add salt and wait before you start the cycle.
Yes, but on a single-tank softener the water you draw during the cycle is not softened. Twin-tank units keep supplying soft water from the second tank. That is why a night-time regeneration makes sense. On a single-tank unit, hot water used during the cycle refills the water heater with hard water.
Watch the water level in the brine tank during the brine-draw stage of a regeneration; your manual says when that stage runs. If the level does not drop then, the injector, the brine line or the float is likely blocked. If the water pressure is low through the softener but recovers when you switch to bypass, the resin bed or the valve may be clogged.
It depends on the capacity of the unit, how much water your household uses and how hard the water is. Harder water uses up the resin faster, so the softener has to regenerate more often. In the Penn State Extension example, four people on 10 grains per gallon need a cycle about every 6 to 7 days.
Leave A Comment